AT&T has usage capped its heavily promoted U-verse GigaPower fiber to the home service at 1TB a month, according to fine print appearing on communications sent to customers.

Any customer that exceeds 1TB of usage per month will be subject to AT&T’s usual overlimit fees: $10 for each additional 50GB of data sent or received. At least AT&T currently caps the maximum overlimit fee at $30 for its fiber customers.

Many Austin GigaPower customers are signing up for the company’s Premier package, which includes a waiver of equipment, installation, and activation fees and provides 36 months of fixed rates and free HBO and HD service along with 300/300Mbps broadband.

Enrolling in a discounted promotional plan does mean you consent to allow AT&T to collect information about your browsing habits through deep packet inspection.

While AT&T trumpets vague plans to upgrade up to 100 cities with gigabit fiber to the home service, some AT&T GigaPower U-verse customers in Austin wish they could just consistently get the 300Mbps service they were promised.

More than a few customers are unhappy with the service they are getting and have been vocal on an AT&T forum with complaints about service interruptions and speed issues.

Among the complaints:

Unresponsive Internet

A common complaint for U-verse GigaPower customers is a suddenly unresponsive Internet.

“Since upgrading to GigaPower often times my browser (same issue with Firefox, Safari, Chrome) will not always load or display web sites. Same thing happens with Tuba and/or Youtube,” writes bcslas. “Often it will fail to load and sometimes I see timeout errors, yet at other times the site loads fine. […] Usually a refresh or 30 second wait to refresh will fix the issue – but it is constant.”

“I upgraded to GigaPower last December and since then, the service started getting disconnected multiple times per week,” wrote ybasha. “Sometimes it lasts a few minutes and sometimes longer. When that happens, I lose Internet and TV service. I called technical support multiple times. They sent technicians twice. One of them swapped the modem, but I still have the problem.”

“When I do a Google search from Chrome, it hangs there until it eventually times out and then I have to reload the page, after which the search results appear,” writes bustedmagnet. “Another example is in Gmail, sometimes the initial page is very slow to load, but it hangs forever when trying to open individual emails. Again, multiple page refreshes seem to fix this.”

It turns out that IPV6, enabled by default, is unreliable when using AT&T GigaPower. Customers have usually found relief downgrading to IPV4-only support or switching to Google’s IPV6 DNS servers:

• 2001:4860:4860::8888
• 2001:4860:4860::8844

Slow Speeds

AT&T GigaPower is supposed to offer 300/300Mbps service today with an upgrade to gigabit Internet forthcoming later this year. But not every customer comes close to getting those speeds. GigaOM writer Stacey Higginbotham found some customers cannot reliably get more than 75Mbps:

Yesterday I was at my brother in-law’s house where he is a GigaPower subscriber, his computer was registering speeds of 70 Mbps down and 50 Mbps up using Ookla on a wired connection. That’s fast, but not 300 Mbps fast and certainly not a gig. My brother and sister-in-law are not speed freaks like myself, but they were disappointed with the GigaPower product.

To me, what was most troubling is that they couldn’t tell me if they had signed up for AT&T’s service plan that offers them a lower price on internet service if the customer lets AT&T use your surfing habits to offer ads. They signed up for a bundle, they said, that was cheaper than their previous service.

“Upload speeds are consistently slower than download speeds,” complained egardiner. “Using att.com/speedtest, I can consistently achieve 320Mbps down, but typically never more than ~180Mbps up. The CrashPlan backup service is glacially slow, never achieving more than 3kbps when sending data to CrashPlan’s cloud servers.  CrashPlan’s techs have suggested that there are no issues on my client PC side nor on their server’s side, and they’ve asked if U-verse GigaPower is throttling backup traffic.”

Broadband Reports’ readers report Usenet newsgroup downloads appear to be heavily throttled over the GigaPower fiber network as well, with speeds dropping well below 100Mbps.

It turns out GigaPower speeds won’t help you with a good Netflix viewing experience either.

“I signed up for the U-Verse GigaPower service and the overall speeds seem to be faster,” writes mstang1988. “The bad, some of regularly used services are not performing. For example, Netflix. On Grande [a competing provider] I was always running at HD. With U-verse I’m seeming giant blocks of blur. I’m fixing to cancel.”

Kim R. in Cedar Falls, Tex. isn’t happy either:

AT&T GigaPower was good for the first 20-30 days, then they made a change and my upload speed is 35-78 on average with a lot of latency and my VoIP phones cannot send or receive calls. Multiple techs were dispatched on Friday and they were at my home for 7+ hours. They eliminated my home as being the source of the issue and other friends in the neighborhood are having the same issues.

We have been in this mode for 4 days now and I have spend most of today working with tech support with no luck. Customer service was no help either when I asked them to suspend billing until they got it working again, of course there answer was “we can’t do that”.

I will loose another day of service when the tech(s) come out again tomorrow. Beware of AT&T’s GigaPower, it’s a myth so far and their techs ride on unicorns and most have no idea about any networking.

At least 46 percent of AT&T’s wireless customers are now paying at least $100 a month for a Mobile Share account with at least a 10GB usage allowance, a dramatic increase of more than 11 million customers during the last three months alone. AT&T customers used to pay a flat rate of $30 a month for unlimited wireless data. Now they pay much, much more for much less usage.

AT&T’s Mobile Share plans start at $20 a month (plus the cost of the device) and include just 300MB of data. Prices escalate from there (all prices don’t include the cost of the device)

• $20 for 300MB
• $25 for 1GB
• $40 for 2GB
• $70 for 4GB
• $80 for 6GB
• $100 for 10GB
• $130 for 15GB
• $150 for 20GB
• $225 for 30GB
• $300 for 40GB
• $375 for 50GB

AT&T is banking on growing mobile data use to earn the company perpetually accelerating revenue and dramatically higher average revenue per customer. The average AT&T customer does not come close to exceeding their current allowance, but the company’s sales force has proven exceptionally adept at convincing customers to upgrade to higher allowance plans whether the customer needs one or not.

One of the first lessons a good magician learns is that to best impress an audience, one has to at least show an actual rabbit going into the hat before making it disappear.

AT&T is no David Copperfield. In its latest sleight of hand, AT&T today announced a major potential expansion of its U-verse GigaPower fiber to the home network to 21 major cities across its landline service area, with future plans to expand to as many as 100 eventually.

“We are excited to bring GigaPower to 100 cities and towns,” Lori Lee, head of AT&T’s U-verse unit, said in a phone interview with Bloomberg, which accompanied a press release. “We will work with local officials as we look for areas of strong demand and pro-investment policy.”

Among the cities slated to get fiber upgrades are Austin and Kansas City — where AT&T will face competition from Google Fiber. But AT&T isn’t bothering to compete head-on with any municipal fiber providers like Chattanooga’s EPB, Wilson, N.C.’s Greenlight, or Lafayette, La.’s LUSFiber. North Carolina, Texas and California are the states with the most cities chosen to potentially get upgrades.

But AT&T has yet to fully deliver on its earlier promise to deploy fiber to the home service in Austin, where single home residential customers have usually been stymied by general unavailability of the fiber service. AT&T has consistently refused to say exactly how many customers have actually been able to sign up for AT&T GigaPower fiber service.

For customers actually able to buy GigaPower, many are already served by an existing AT&T fiber cable. It is not uncommon to find fiber hookups in new housing developments or multi-dwelling units like apartment buildings and condominiums. Most customers don’t realize they are fed service from a fiber cable brought to the back of the building that interfaces with plain old copper wiring, providing service artificially slowed by the company in an effort to provide consistently marketed broadband products.

AT&T GigaPower is easy to provide in these locations with very little extra investment. Tearing up streets and yards to replace copper wiring with fiber optics is another matter, one AT&T has avoided for years by choosing a less costly fiber to the neighborhood approach that leaves existing copper wiring on phone poles and in customer homes largely intact. Moving to fiber to the home service would require AT&T to dramatically boost capital spending to cover the cost of stringing fiber across the backyards of millions of customers.

But earlier this year, AT&T promised investors it was actually planning to cut its budget for capital expenses in 2014 to $21 billion, most of that still earmarked for its profitable wireless network. That is down at least $200 million from 2013. Unless AT&T reneges on its earlier commitment to Wall Street, even David Copperfield couldn’t make fiber to the home service from AT&T magically appear.

Welcome to Neverland. Despite exciting press releases, AT&T has indicated it won’t spend the money required for widespread fiber expansion. But then, AT&T’s own graphics only promise these communities “may” get GigaPower.

In fact, AT&T has been telling investors it is more than halfway done completing its Project VIP effort, which budgeted $14 billion over three years to further expand basic U-verse service, improve its 4G LTE network, and expand rural wireless coverage within AT&T local service areas. Project VIP is integral to AT&T’s plan to eventually walk away from its rural wired infrastructure in favor of a wireless platform providing wireless landline service and 4G wireless broadband.

To assuage investors fearing AT&T is about to pull out the credit card and go on a fiber broadband shopping spree, AT&T carefully notes towards the bottom of its press release, “this expanded fiber build is not expected to impact AT&T’s capital investment plans for 2014.”

In other words, AT&T is not committing any money not already earmarked as part of Project VIP for its fiber expansion.

Without that money, if you live in a single-family residential home and are currently served by AT&T copper wiring, it is very unlikely the company will offer fiber upgrades anytime soon.

So why is AT&T promising vaporware upgrades it cannot possibly manage on its current budget?

AT&T will work with local leaders in these markets to discuss ways to bring the service to their communities. Similar to previously announced metro area selections in Austin and Dallas and advanced discussions in Raleigh-Durham and Winston-Salem, communities that have suitable network facilities, and show the strongest investment cases based on anticipated demand and the most receptive  policies will influence these future selections and coverage maps within selected areas. This initiative continues AT&T’s ongoing commitment to economic development in these communities, bringing jobs, advanced technologies and infrastructure.

Phillip “AT&T has a larger agenda here and it isn’t fiber” Dampier

For years, AT&T’s lobbyists have promised politicians everything under the sun — telecom nirvana — if only Ma Bell can be unshackled by burdensome regulations. Some states have accepted AT&T’s deal only to find their residents’ phone bills rapidly increasing with no corresponding improvement in service. U-verse is AT&T’s effort to stay relevant at a time when mobile phones are replacing landlines and cable companies have poached a number of their customers.

But in return for that deregulation, AT&T delivered an cheaper, inferior fiber-to-the-neighborhood technology that requires hideously large infrastructure cabinets, often installed in front of customer homes, that has trouble keeping up with cable broadband speeds.

But nothing ever satisfies AT&T.

Recently, their lobbyists have been skulking around in the shadows of state legislatures ghostwriting new bills that would permit AT&T to abandon its rural landline customers altogether to focus on the far more profitable wireless business. But consumer groups have gotten wise to AT&T’s astroturf and lobbying efforts and have begun to limit their successes.

Meanwhile, along comes Google, promising groundbreaking, affordable fiber to the home gigabit broadband service to a handful of communities willing to work with them in a de facto partnership — cutting through bureaucratic red tape to facilitate infrastructure upgrades — a radical change from the traditional regulator-provider framework.

Hundreds of cities fell all over themselves competing for the privilege, and it didn’t require a penny in lobbying or campaign contributions.

Where Google has been willing to offer service, most communities have been more than thankful and have made life easier for the creative entrant.

If it worked for Google, why can’t it work for AT&T? As a result, the company that spent years telling customers fiber upgrades didn’t make any sense and that few people actually needed gigabit speeds, AT&T might appear to have reversed course. Dig a little deeper and you find a deeper agenda:

“Communities that have suitable network facilities, and show the strongest investment cases based on anticipated demand and the most receptive policies will influence these future selections and coverage maps within selected areas.”

Translation: Communities that already have considerable fiber infrastructure previously installed and are willing to bend to the business and public policy agenda of AT&T will make all the difference whether your city will be considered for a future fiber upgrade or not.

In the end, even if a community does everything AT&T asks of it, it still has no commitment AT&T will actually deliver the fiber upgrades they only promise “may” happen. But AT&T will have achieved its public policy goals of abolishing regulations and limiting oversight, all without have to install a single strand of fiber.

That is a deal community leaders should think twice about making with a company that has always looked out for its investors long before its customers.

AT&T U-verse with Gigapower is not coming to a home near you, although AT&T hopes you believe it will.

In the public and government relations arena, convincing everyone there is robust competition in broadband is a good prescription to keep the regulators at bay. To make that happen, AT&T continues to roll out more press releases than actual fiber to the home service, this time announcing it is planning to bring its fastest gigabit Internet service to “six cities in North Carolina” and more areas in and around Austin.

“The U-verse GigaPower fiber-optic service will be offered in parts of Carrboro, Cary, Chapel Hill, Durham, Raleigh and Winston-Salem, North Carolina,” AT&T said today in a statement.

But AT&T will not say exactly how many homes it will offer service to, but gave a clue mentioning it plans to connect as many as 100 businesses and 100 “public sites.” It also said it will provide a free, but slow-speed service to as many as 3,000 homes — something it can offer on its existing copper-fiber U-verse platform.

AT&T claims it is ‘racing’ to offer fiber service, but evidence suggests otherwise. Much of AT&T’s U-verse with Gigapower is turning up in condos, new housing developments, and other multi-dwelling units like apartments. Single family homes are evidently not a priority. AT&T’s costs to bring fiber to the back of a complex or large apartment building is lower than stringing or burying fiber to individual homes.

In Austin, one of AT&T’s major Gigapower expansions will come to communities under construction and condo complexes developed by PulteGroup. AT&T signed a favorable agreement with the developer to bring fiber into up to 3,000 homes. AT&T routinely signs similar agreements with developers that offer AT&T exclusive access to existing inside wiring and, in some cases, provide AT&T services to every resident, billed as part of the rent or neighborhood association service fees, deterring competition from cable operators.

AT&T likely selected the communities in North Carolina after receiving a Request For Proposals from a regional group called North Carolina Next Generation Network, which has enticed private providers to build gigabit fiber networks. The coordinated effort is led by six municipalities and four leading research universities and supported by local Chambers of Commerce and businesses in the Research Triangle and Piedmont regions.

With local governments directly involved in the initiative, AT&T was likely satisfied they would not face much difficulty from zoning and permitting procedures to expand their network, and might even receive favorable treatment.